August/2019 Braindump2go 300-115 Exam Dumps with PDF and VCE New Updated Today! Following are some 300-115 Real Exam Questions:

1.|2019 Latest Braindump2go 300-115 Exam Dumps (PDF & VCE) Instant Download:

2.|2019 Latest Braindump2go 300-115 Exam Questions & Answers Instant Download:

Real Questions
What is the Ethernet frame size for 802.1Q?

A. 64
B. 128
C. 1518
D. 1522

Answer: D

Real Questions
How will the traffic reach the core switch from AS switch to DS core switch?\

(Based on a topology shown with one core, two distribution and two access switches on each distribution switch, with redundant links and bandwidth mentioned.)

A. ASW1 to DWS1 to core
B. ASW1 to DWS2 to core
C. ASW1 to DSW1 to DSW2 to core
D. ASW1 to DSW2 to DSW1 to core

Answer: B

Real Questions
If HSRP group number is 45 what would be the MAC address?
(Basically conversion of digit to hexadecimal with group of 16.)

A. 00-00-0C-07-AC-2D
B. 0000-0C07-AC45
C. 0000-070C-AC2D
D. 0000-C004-ACD2

Answer: A
00-00-0c- 07-ac-2D

Real Questions
Select a valid VRRP configuration from a list of possible configurations. (Choose three.)

A. vrrp [group-number] ip [ip-address]
B. vrrp [group-number] priority [priority]
C. vrrp [group-number] preempt
D. standby [group number] priority [priority]
E. standby [group number] preempt

Answer: ABC
You can eliminate configurations with the word `standby’, as that would be HSRP, not VRRP. Also, I think the options that put things like vrrp group 1 ip x.x.x.x are wrong.
You don’t need the word `group’ in the configuration line. The number 1 is the group number. Anyway, just take a good look a t a few valid VRRP configuration examples so that you will be able to recognize invalid ones.

Real Questions
Which two secondary VLAN types of Private VLANs (PVLANs)? (Choose Two)

A. community
B. isolated
C. promiscuous
D. host

Answer: AB
Secondary VLANs provide Layer 2 isolation between ports within the same private VLAN domain.
There are two types of secondary VLANs:
• Isolated VLANs – Ports within an isolated VLAN cannot communicate with each other at the Layer 2 level.
• Community VLANs – Ports within a community VLAN can communicate with each other but cannot communicate with ports in other communities at the Layer 2 level

Real Questions
What types of SDM templates you can use in switch? (Choose four)

A. Access
B. Default
C. Routing

Answer: ABCD
+ Access – The access template maximizes system resources for access control lists (ACLs) to accommodate a large number of ACLs.
+ Default – The default template gives balance to all functions.
+ Routing – The routing template maximizes system resources for IPv4 unicast routing, typically required for a router or aggregator in the center of a network.
+ VLANs – The VLAN template disables routing and supports the maximum number of unicast MAC addresses. It would typically be selected for a Layer 2 switch.

Real Questions
What is the process to configure EtherChannel?

A. shutdown both interface ports
B. shutdown the interface on one side only
C. Shutdown is necessary if the ports are in err-disable
D. Don’t need to shutdown the ports

Answer: A

Real Questions
A question about spanning-tree port-priority.

A. 127
B. 129
C. 128
D. 4096

Answer: A
If all priorities are default the value is 128.
Lesser is better in this case, the only one answer who has the less value in this case is 127.

Real Questions
Spanning-tree EtherChannel misconfiguration

A. (config)#spanning-tree etherchannel guard misconfig
B. (config-if)#spanning-tree etherchannel guard misconfig
C. (config)# spanning-tree etherchannel misconfig guard
D. (config-if)# spanning-tree etherchannel misconfig guard

Answer: A
Enabling EtherChannel Guard guide/3750xscg/swstpopt.html

Real Questions
There was another Exhibit about port priority- Core switch connected to 2 dis switches which connected 2 ASW. PC1 is connected to DSW1 and DSW2 (Root Bridge). Link connected from PC1 to DSW2 is 4Gbps and DSW1 is 10Gbps. There is etherchannel trunk between DSW1 and DSW2. Default port prioirty is configured.
Change in port priority so traffic goes through DSW1 to DSW2

A. DSW1: spanning-tree port priority 16
B. DSW1: interface g1/0
C. DSW2: spanning-tree port priority 16
D. DSW2: interface g1/0
E. DSW1: spanning-tree port priority 0

Answer: AB

Real Questions
If EtherChannel guard is configured, how the interface status is (or looks like) if misconfigured?

A. errdisabled
B. shutdown

Answer: A


1.|2019 Latest Braindump2go 300-115 Exam Dumps (PDF & VCE) Instant Download:

2.|2019 Latest Braindump2go 300-115 Study Guide Video Instant Download: